MED9 Abbreviations in English (R-S)
From Nefmoto
|
RADU |
wheel circumference |
|
RADU |
wheel circumference |
|
RADUDR |
wheel circumference, driven wheel |
|
RALEMAX |
Limitation for max turnback angle |
|
RAMPASR |
ramp steepness during advancement of ASR torque request |
|
RAMPTRTRQD |
Integration constant to ramp down the engine torque during the transmission over |
|
RAMPTRTRQU |
Integration constant to ramp up the engine torque during the transmission overhe |
|
RBELH |
On-load resistance for pump current generation downstr. cat |
|
RDEPHNMIN |
Reverse rotation detection via camshaft: time debouncing for reseting B_rdph aft |
|
RDEPHPRMX |
Reverse rotation detection via camshaft: max. countervalue for debouncing |
|
RDHDEVOCTR |
Number of synchros to reset counters |
|
RDUNDEF |
angle range within there is no validity of the reverse detection |
|
RDUNDEFR |
undefined angle range in reverse-running detection |
|
REAC_T2_UC |
Fault time function monitoring - fault reaction monitoring in instruction test |
|
REAC_T2_UM |
Fault time for function monitoring - fault reaction monitoring in UF |
|
REAC_T3_UC |
Fault time for checking ignition cut off in the instruction test |
|
REAC_T3_UM |
Fault time for checking ignition cut off in the fault reaction monitoring |
|
RECIKAPPA |
Reversed value of the isentropic exponent |
|
RECIKAPPA |
Reversed value of the isentropic exponent |
|
REDABM |
fuel cut-off table for torque reduction |
|
REDHYOC |
hysteresis of reduction step at bigger desired red. step than actual value |
|
REDHYUC |
hysteresis of reduction step at smaller desired red. step than actual value |
|
REDMXMSV |
maximal step number for MSV off |
|
REDMXSA |
maximum reduction step for sequential fuel cutoff |
|
REDZEM |
threshold between ignition intervention and injector disabling |
|
REDZEMNL |
threshold between ignition intervention and injector disabling, emerg. mode |
|
REFINI |
initial value for reference level if knock control enabled |
|
REMRVSMX |
number of remote start attempts allowed |
|
RESFDSHMX |
Threshold for response time of oxygen sensor downstream front catalyst |
|
RESFDSHMX |
Threshold for response time of oxygen sensor downstream front catalyst |
|
RESFDSHMX |
Threshold for response time of oxygen sensor downstream front catalyst |
|
RFAAAA |
Dummy fid: Relationship fid -> dfp (Mode A) |
|
RFAAAA |
Dummy fid: Relationship fid -> dfp (Mode A) |
|
RFAAAA |
Dummy fid: Relationship fid -> dfp (Mode A) |
|
RFAFRA |
relationship fid to dfp: Mode A, range FRA of LRA |
|
RFAFRAT |
|
|
RFAORA |
relationship fid to dfp: Mode A, range ORA of LRA |
|
RFATEH |
relationship fid to dfp: Mode A, purge control at high load |
|
RFATEL |
relationship fid to dfp: Mode A, purge control at low load |
|
RFATEN |
emergency canister purge contributes to this fault path (DFP) |
|
RFATLDI |
|
|
RFATLDO |
|
|
RFBAAA |
Dummy fid: Relationship fid -> dfp (Mode B) |
|
RFBDLSU |
|
|
RFBFRST |
relationship fid to dfp: Mode B, short test of close loop control |
|
RFBHKT |
Fault path computed by DKATSP |
|
RFBHKT2 |
Fault path computed by DKATSP |
|
RFBLASH |
relationship fid to dfp: Mode B, function DLSAHK |
|
RFBLLRH |
idlespeed deviation HOM contributes to this fault path (DFP) |
|
RFBLLRKH |
idle speed control diagnosis contributes to this fault path (DFP) |
|
RFBPLSU |
|
|
RFCAAA |
|
|
RFCANWS |
DFP receiv. contrib. of diagnosis camshaft actuator exhaust |
|
RFCBKVP |
|
|
RFCBSTHD |
|
|
RFCDEONV |
|
|
RFCDSHK |
|
|
RFCDSKVR |
|
|
RFCDSTD |
|
|
RFCDSTR |
|
|
RFCDVEL |
|
|
RFCDVER |
|
|
RFCDWVA |
Fault path computed by DWVNWKW Auslass-NW 1 |
|
RFCDWVE |
Fault path computed by DWVNWKW Einlass-NW 1 |
|
RFCDYSH |
|
|
RFCENWS |
DFP receiv. contrib. of diagnosis camshaft actuator inlet |
|
RFCFCSFP |
|
|
RFCFDLA |
|
|
RFCFST |
|
|
RFCHFMR |
|
|
RFCHSHK |
|
|
RFCHSV |
|
|
RFCHSVS |
|
|
RFCIMP1P |
DFP receiv. contrib. of IUMPR-General Denominator w/ poti1-fault |
|
RFCIMP2P |
DFP receiv. contrib. of IUMPR-General Denominator w/ poti2-fault |
|
RFCIMPGD |
DFP receiv. contrib. of IUMPR-General Denominator |
|
RFCIMPIC |
DFP receiv. contrib. of IUMPR-Ignition Cycle Counter |
|
RFCLSH |
|
|
RFCNLHP |
|
|
RFCNLLP |
|
|
RFCNLPL |
|
|
RFCNLPS |
|
|
RFCNWKWA |
|
|
RFCNWKWA2 |
|
|
RFCNWKWB1 |
|
|
RFCNWKWB2 |
|
|
RFCNWKWE |
|
|
RFCNWKWE2 |
|
|
RFCNWVA |
DFP receiv. contrib. of diagnosis of locked camshaft actuator exhaust |
|
RFCNWVE |
DFP receiv. contrib. of diagnosis of locked camshaft actuator inlet |
|
RFCPBKVR |
|
|
RFCPLSU |
|
|
RFCPSRR |
|
|
RFCPUR |
|
|
RFCPVDR |
|
|
RFCSTHDR |
|
|
RFCSUVRH |
|
|
RFCSUVRP |
|
|
RFCTABSS |
|
|
RFCTABST |
|
|
RFCTACS |
|
|
RFCTAHCS |
|
|
RFCTAHR |
|
|
RFCTAR |
|
|
RFCTES |
relationship fid to dfp: Mode C, evap system monitoring |
|
RFCTESF |
|
|
RFCTESG |
|
|
RFCTESK |
relationship fid to dfp: Mode C, evap syst. monit. smallest leak |
|
RFCTH |
|
|
RFCTM |
|
|
RFCTMCS |
|
|
RFCULSU |
|
|
RFCVFZ |
|
|
RFCZWP |
|
|
RFCZZZ |
|
|
RGAAAA |
Dummy fid: upper limit of ramp priority (Mode A) |
|
RGAAAA |
Dummy fid: upper limit of ramp priority (Mode A) |
|
RGAFRA |
upper limit of ramp priority: Mode A, range FRA of LRA |
|
RGAFRAT |
|
|
RGAORA |
upper limit of ramp priority: Mode A, range ORA of LRA |
|
RGATEH |
upper limit of ramp priority: Mode A, purge control at high load |
|
RGATEL |
upper limit of ramp priority: Mode A, purge control at low load |
|
RGATEN |
upper limit of ramp priority RPRATEN of emergency canister purge |
|
RGATLDI |
|
|
RGATLDO |
|
|
RGBAAA |
Dummy fid: upper limit of ramp priority (Mode B) |
|
RGBDLSU |
|
|
RGBFRST |
upper limit of ramp priority: Mode B, short test of close loop control |
|
RGBHKT |
Upper limit of ramp priority RPR of DKATSP |
|
RGBHKT2 |
Upper limit of ramp priority RPR of DKATSP |
|
RGBLASH |
upper limit of ramp priority: Mode B, function DLSAHK |
|
RGBLLRH |
upper limit of ramp priority RPRBLLRH of idlespeed deviation HOM |
|
RGBLLRKH |
upper limit of ramp priority rprbllrkh of idle speed control diagnosis |
|
RGBPLSU |
|
|
RGCAAA |
Dummy fid: upper limit of ramp priority (Mode C) |
|
RINCAL |
calibration resistance for internal resistance of Nernst cell |
|
RINDYNH |
Lim. value internal resistance Nernst cell of dynamic LSF downstream cat. |
|
RINHAB |
Limit internal resistance Ri of the Nernst sensor downstream cat for B_shab |
|
RINHMX |
Limit internal resistance Ri of the Nernst sensor downstream cat to max. value |
|
RININI |
Initializ. value of rinlsu_w (resist. value of the Nernst cell LSU) |
|
RINNPH |
Threshold to detect condition ""Ri is too high"" |
|
RISIGRESH |
threshold for reset wiring-interruption with Ri-diagnosis downstr. cat |
|
RKAMX_UC |
RKAMX_UM at instruction test |
|
RKAMX_UM |
max. permissible value of additve air-fuel-adaption at monitoring function |
|
RKAPP |
application value for rk |
|
RKBAUM |
rk-threshold for acceleration enrichment display |
|
RKC_MODUFOL_UC |
|
|
RKLLMX |
lambda deviation at max. ora_w in idle speed |
|
RKMINHDP |
|
|
RKMNHDP |
Min. required fuel mass for plausibility check of high-pressure-system |
|
RKMSVZPAH |
hysteresis of threshold relative fuel mass MSV two-point-control |
|
RKMXHDP |
Max. fuel mass for plausibility check of high-pressure-system |
|
RKO_UC |
Offset tolerance value of the instruction test |
|
RKO_UM |
Offset tolerance value of the function monitoring |
|
RKRMX1N |
Maximum of reference level for knock detection threshold cylinder group 1 |
|
RKRMX2N |
maximum of reference level for knock detection threshold cylinder group 2 |
|
RKSPH |
Resistance between congruent voltage and sensor signal downstr. cat |
|
RKTEO_UC |
offset for check of minimal rkte from purge control in instruction test |
|
RKTEO_UM |
offset for check of minimal rkte from purge control in function monitoring |
|
RKTI_T_UM |
fault tolerance time for rk-ti check |
|
RKUKGMN |
min. rel. fuel mass transition compensation |
|
RKVAUM |
rk-threshold for deceleration enleanment display |
|
RLC_T_UC |
Fault tolerance time for rl comparison with the function in instruction test |
|
RLC_T_UM |
Fault tolerance time for rl comparison with the function in function monitoring |
|
RLDV |
Detection error of speed signal due to realtive load signal |
|
RLDYNFAW |
Load threshold for dynamics check LSU at funktion request (16 Bit) |
|
RLDYNOW |
Upper load threshold for dynamics check LSU (16 Bit) |
|
RLDYNUW |
Lower load threshold for dynamics check LSU (16 Bit) |
|
RLKTDMN |
minimum relative air charge for catalyst diagnosis |
|
RLKTDMNT |
minimum relative air charge for catalyst diagnosis, functional test |
|
RLKTDMX |
maximum relative air charge for catalyst diagnosis |
|
RLKTDMXT |
maximum relative air charge for catalyst diagnosis, functional test |
|
RLLRHON |
char. line on nmot, upper rl control threshold for downstream lambda control |
|
RLLRHUN |
char. line on nmot, lower control threshold rl for downstream lambda control |
|
RLLRUN |
char.line above nmot,lower rL control limit for controller in front of catalyst |
|
RLMDVERL |
intake gas threshold for for idle speed diagnosis ;dep. on accessory load |
|
RLMILOWRM |
Max. engine load for masking out MIL-blinking due to cat damaging misfire |
|
RLMNHSPKH |
Minimum air charge for request of hom.split injection for cat. heating |
|
RLMNN |
characteristic minimum charge |
|
RLMNSAN |
characteristic minimum charge in overrun |
|
RLMXDHDEVO |
load threshold for function DHDEVO |
|
RLMXELDR |
maximum air charge for protection against overboost in case of E_ldr |
|
RLMXHDEV |
max. allowed charge in case of open clamping HPIV |
|
RLNOT |
limp-home relative air charge rl in case of E_DK and E_LM |
|
RLO1 |
upper load-signal threshold range 1 |
|
RLO1M |
upper load-signal threshold range 1 at lean mode |
|
RLO2 |
upper load threshold of range 2 |
|
RLO2M |
upper load threshold of range 2 at lean mode |
|
RLO3 |
upper load-signal threshold range 3 |
|
RLO3M |
upper load-signal threshold range 3 at lean mode |
|
RLPO_UC |
Offset tolerance value of the instruction test |
|
RLPO_UM |
Offset tolerance value of the function monitoring |
|
RLP_T_UC |
verification time for deviation between rl and rlp in instruction test |
|
RLP_T_UM |
verification time for deviation between rl and rlp in func. mon. |
|
RLSOLAP |
desired relative air charge (application mode) |
|
RLSOLAPW |
rlsol-demand by characteristic line for application |
|
RLU1 |
lower load-signal threshold range 1 |
|
RLU1M |
lower load-signal threshold range 1 at lean mode |
|
RLU2 |
lower load-signal threshold range 2 |
|
RLU2FA |
lower load-signal threshold range 2 at function-requirement (B_falra) |
|
RLU2M |
lower load-signal threshold range 2 at lean Mode |
|
RLU3 |
lower load-signal threshold range 3 |
|
RLU3M |
lower load-signal threshold range 3 im Magerbetrieb |
|
RMLSCD |
Difference of load with stored value to determine the similar conditions window |
|
RMLSCDP |
Difference of load with stored value to determine the similar conditions window |
|
ROMRSTA_UM |
Max. number of resets for error detection in the ROM check during initialization |
|
ROVEVABMX |
Maximal oxygen fraction from before cut-off for validation of the measurement |
|
RSOXABST |
Oxygen storage rate during stop time |
|
RSTEP |
threshold: ratio of OSC value to modell value to trigger Step Change |
|
RSTEPC |
threshold: ratio of OSC value to modell value to confirm Step Change |
|
RSTHDREBF |
Number of synchros for waiting on high fuel pressure at initial fueling mode |
|
RTDBIHT |
braking input hold time (RTD) |
|
RTDDISTCD |
desired throttle clutch dump (RTD) |
|
RTDDTCA1 |
delta torque coefficient A1 (RTD) |
|
RTDDTCA2 |
delta torque coefficient A2 (RTD) |
|
RTDDTCB0 |
delta torque coefficient B0 (RTD) |
|
RTDDTCB2 |
delta torque coefficient B2 (RTD) |
|
RTDDTDIV |
delta torque divisor (RTD) |
|
RTDDTGM |
delta torque gear mult (RTD) |
|
RTDESCD |
engine speed clutch dump (RTD) |
|
RTDLDAT |
lift dive active time (RTD) |
|
RTDLDTT |
lift dive test time (RTD) |
|
RTDMTGUD |
manual transmission shift gear update delay (RTD) |
|
RTDNDTL |
Negative delta torque limiter (RTD) |
|
RTDPDTL |
positive delta torque limiter (RTD) |
|
RTDRRVSSFD |
rough road VSS filter disable (RTD) |
|
RTDTBA |
throttle braking acceleration (RTD) |
|
RTDVABA |
vehicle acceleration braking acceleration (RTD) |
|
RTDVABD |
vehicle acceleration braking deceleration (RTD) |
|
RTDVAFCA1 |
vehicle acceleration filter coefficient A1 (RTD) |
|
RTDVAFCA2 |
vehicle acceleration filter coefficient A2 (RTD) |
|
RTDVAFCB0 |
vehicle acceleration filter coefficient B0 (RTD) |
|
RTDVAFCB1 |
vehicle acceleration filter coefficient B1 (RTD) |
|
RTDVAFCB2 |
vehicle acceleration filter coefficient B2 (RTD) |
|
RTDVAFDIV |
vehicle acceleration filter divisor (RTD) |
|
RTDVALFCA1 |
vehicle acceleration lag filter coefficient A1 (RTD) |
|
RTDVALFCA2 |
vehicle acceleration lag filter coefficient A2 (RTD) |
|
RTDVALFCB0 |
vehicle acceleration lag filter coefficient B0 (RTD) |
|
RTDVALFCB1 |
vehicle acceleration lag filter coefficient B1 (RTD) |
|
RTDVALFCB2 |
vehicle acceleration lag filter coefficient B2 (RTD) |
|
RTDVALFDIV |
vehicle acceleration lag filter divisor (RTD) |
|
RTDVSCD |
vehicle speed clutch dump (RTD) |
|
RTDVSSBE |
VSS braking enable (RTD) |
|
RTEHKMX |
Max threshold in case of canister purge |
|
RTIMELIM_RDI |
|
|
Rtmo_adCallingBegin_cu32 | |
|
Rtmo_adCallingEnd_cu32 | |
|
Rtmo_adStart_cu32 |
|
|
Rtmo_stIntOverhead_cu8 | |
|
Rtmo_stSampleTime_cu8 | |
|
Rtmo_swLoadMode_cu8 | |
|
Rtmo_swMode_cu8 |
|
|
RVSDISCODE |
Code PID $1551 - Remote Vehicle Start Disable History |
|
RVSNENCODE |
Code PID $1551 - Remote Vehicle Start Disable History |
|
S6D8180 |
mode6-DFP for additive correction |
|
S6D8182 |
mode6-DFP for multiplicative correction |
|
SAAAAA |
Dummy fid: Slope in active phase (Mode A) |
|
SAAAAA |
Dummy fid: Slope in active phase (Mode A) |
|
SAABOMX |
max. number of cold starts (abo) to release fuel cut off adaptation |
|
SAAFRA |
slope in active phase: Mode A, range FRA of LRA |
|
SAAFRAT |
|
|
SAAORA |
slope in active phase: Mode A, range ORA of LRA |
|
SAATEH |
slope in active phase: Mode A, purge control at high load |
|
SAATEL |
slope in active phase: Mode A, purge control at low load |
|
SAATEN |
negative slope of ramp priority RPRATEN; emergency canister purge active |
|
SAATLDI |
|
|
SAATLDO |
|
|
SABAAA |
Dummy fid: Slope in active phase (Mode B) |
|
SABDLSU |
|
|
SABFRST |
slope in active phase: Mode B, short test of close loop control |
|
SABHKT |
Negative slope of ramp priority RPR DKATSP (active) |
|
SABHKT2 |
Negative slope of ramp priority RPR DKATSP (active) |
|
SABLASH |
slope in active phase: Mode B, function DLSAHK |
|
SABLLRH |
negative slope of ramp priority RPRBLLRH; idlespeed deviation HOM active |
|
SABLLRKH |
negative slope of ramp priority rprbllrkh; idle speed control diagnosis active |
|
SABPLSU |
|
|
SACAAA |
Dummy fid: Slope in active phase (Mode C) |
|
SADYNINI |
Initialisation value for dynamic filter |
|
SADYNMX |
Max. dynamic behavior to activate adjustment of LSU in air |
|
SAFT1 |
filter time constant 1 for lambda sensor signal access |
|
SALSUMN |
min. number of fuel cut off periods |
|
SALSUMNS |
min. number of fuel cut off periods for fast adaptation |
|
SAMSABGMN |
min. air mass flow for fuel cut off adaptation |
|
SAMSABGMX |
max. air mass flow for fuel cut off adaptation |
|
SATMOT |
Min. motor temperature to activate adjustment of LSU in air |
|
SATMOTMN |
Min, threshold for engine temperature to enable fuel cut off adaptation |
|
SATUMG |
Max. allowable air temperature to activate adjustment of LSU in air |
|
SDHDRMN |
threshold minimum error HDR |
|
SDHDRMX |
threshold maximum error HDR |
|
SDHDRNPL |
threshold not plausible error HDR |
|
SDHDRSIG |
threshold not plausible error HDR |
|
SDLAFTMN |
minimum (lower) fault theshold for dlatrmo_w for fueltrim fault |
|
SDLAFTMX |
maximum (upper) fault theshold for dlatrmo_w for fueltrim fault |
|
SDLAOFMN |
minimum (lower) fault theshold for dlahii_w |
|
SDLAOFMN |
minimum (lower) fault theshold for dlahii_w |
|
SDLAOFMN |
minimum (lower) fault theshold for dlahii_w |
|
SDLAOFMX |
maximum (upper) fault theshold for dlahii_w |
|
SDLAOFMX |
maximum (upper) fault theshold for dlahii_w |
|
SDLAOFMX |
maximum (upper) fault theshold for dlahii_w |
|
SDMGLVU |
lower threshold of driving distance from refueling to supposed rough leak |
|
SDMGLVU |
lower threshold of driving distance from refueling to supposed rough leak |
|
SDMRKHZWMN |
threshold for dmrkh to select the ramp-steepness in ZWMIN_POSTSTART |
|
SECTEMDGN |
Secondary tank empty diagnosis |
|
SECTEMPDSP |
Secondary tank Empty Display |
|
SECTESDGN |
Secondary Tank Estimate Diagnosis |
|
SECTESDSP |
Secondary Tank Estimate Display |
|
SEGMANSW |
segment count threshold for switching to multiples of segments for mean value |
|
SENLRHLR |
Threshold of enable mean value of B_lr |
|
SEONVDISMN |
required minimum distance for EONV start by tester |
|
SFAAAA |
Dummy fid: skale factor for physical priority (mode A) |
|
SFAAAA |
Dummy fid: skale factor for physical priority (mode A) |
|
SFAFRA |
scale factor for phys. urgency: Mode A, range FRA of LRA |
|
SFAFRAT |
|
|
SFAORA |
scale factor for phys. urgency: Mode A, range ORA of LRA |
|
SFATEH |
scale factor for phys. urgency: Mode A, purge control at high load |
|
SFATEL |
scale factor for phys. urgency: Mode A, purge control at low load |
|
SFATEN |
priority scaling factor for PHUATEN of emergency canister purge |
|
SFATLDI |
|
|
SFATLDO |
|
|
SFBAAA |
Dummy fid: skale factor for physical priority (mode B) |
|
SFBDLSU |
|
|
SFBFRST |
scale factor for phys. urgency: Mode B, short test of close loop control |
|
SFBHKT |
Priority scaling factor for PHU of DKATSP |
|
SFBHKT2 |
Priority scaling factor for PHU of DKATSP |
|
SFBLASH |
scale factor for phys. urgency: Mode B, function DLSAHK |
|
SFBLLRH |
priority scaling factor for PHUBLLRH of idlespeed deviation HOM |
|
SFBLLRKH |
priority scaling factor for phubllrkh of idle speed control diagnosis |
|
SFBPLSU |
|
|
SFCAAA |
Dummy fid: skale factor for physical priority (mode C) |
|
SFEONVA |
threshold of canister load factor for EONV abortion |
|
SFOFTM |
threshold value tmot for fuel-off adaptation activ |
|
SFONTM |
threshold value tmot for fuel-on adaptation activ |
|
SFTEDA05 |
max. threshold of HC-charge for allowed leak diagnose (0.5mm check) |
|
SFTEDAO05 |
upper threshold of HC-charge for allowed leak diagnose (0.5mm check) |
|
SGSC_T_UC |
Fault time for SGS intervention surveillance in instruction test |
|
SGSC_T_UM |
Fault time for SGS intervention surveillance in function monitoring |
|
SGSMDTMX |
Max. torque-time surface SGS-pot plausibility |
|
SGSNU_T_UC |
Debounce time for failure in SGS alive check for instruction test |
|
SGSNU_T_UM |
debounce time for failure in SGS alive check for the function monitoring |
|
SIAAAA |
Dummy fid: Slope in idle phase (Mode A) |
|
SIAAAA |
Dummy fid: Slope in idle phase (Mode A) |
|
SIAFRA |
slope in idle phase: Mode A, range FRA of LRA |
|
SIAFRAT |
|
|
SIAORA |
slope in idle phase: Mode A, range ORA of LRA |
|
SIATEH |
slope in idle phase: Mode A, purge control at high load |
|
SIATEL |
slope in idle phase: Mode A, purge control at low load |
|
SIATEN |
positive slope of ramp priority RPRATEN; emergency canister purge inactive |
|
SIATLDI |
|
|
SIATLDO |
|
|
SIBAAA |
Dummy fid: Slope in idle phase (Mode B) |
|
SIBDLSU |
|
|
SIBFRST |
slope in idle phase: Mode B, short test of close loop control |
|
SIBHKT |
Positive slope of ramp priority RPR DKATSP (inactive) |
|
SIBHKT2 |
Positive slope of ramp priority RPR DKATSP (inactive) |
|
SIBLASH |
slope in idle phase: Mode B, function DLSAHK |
|
SIBLLRH |
positive slope of ramp priority RPRBLLRH; idlespeed deviation HOM inactive |
|
SIBLLRKH |
positive slope of ramp priority rprbllrkh; idle speed control diagnosis inactive |
|
SIBPLSU |
|
|
SICAAA |
Dummy fid: Slope in idle phase (Mode C) |
|
SK_TMR_STR |
|
|
SLFOFO1 |
upper threshold for learning filter value at fuel-off adaptation |
|
SLFOFO2 |
upper threshold for learning filter value at fuel-off adaptation |
|
SLFOFU1 |
lower threshold for learning filter value at fuel-off adaptation |
|
SLFOFU2 |
lower threshold for learning filter value at fuel-off adaptation |
|
SLFOO1N |
speed dep. upper threshold for learning filter value at fuel-on/-off adaptation |
|
SLFOO2N |
speed dep. upper threshold for learning filter value at fuel-on/-off adaptation |
|
SLFOU1N |
speed dep. lower threshold for learning filter value at fuel-on/-off adaptation |
|
SLFOU2N |
speed dep. lower threshold for learning filter value at fuel-on/-off adaptation |
|
SMLDYN |
air mass threshold for sensor dynamic downstream KAT |
|
SOPOF |
position of lambda sensor downstream pre-catalyst |
|
SOPOH |
position of lambda sensor downstream catalyst |
|
SOPOV |
position of lambda sensor upstream catalyst |
|
SOXIDYLSH |
air mass threshold for dynamic measurement of sensor downstream cat |
|
SOXIHIMP |
|
|
SP12LL_UM |
maximum difference between SP1S and SP2S below full load |
|
SP12VG_UM |
maximum difference between SP1S and SP2S above full load range |
|
SPDPERF1 |
Speed for performance launch calculation |
|
SPDPERF2 |
Speed for performance launch calculation |
|
SPDPERF3 |
Speed for performance launch calculation |
|
SPSCO_UC |
Pedal full load limit for function monitoring for instruction test |
|
SPSCO_UM |
Pedal full load limit for function monitoring |
|
SPSCU_UC |
Pedal idle limit for function monitoring in instruction test |
|
SPSCU_UM |
Pedal idle limit for function monitoring |
|
SPSC_MINUM |
|
|
SPSC_T_UM |
Fault time for nominal values in func. monitor. which are mutually not plaus. |
|
SPSNLL_UC |
Maximum voltage for accelerator pedal at idle in instruction test |
|
SPSNLL_UM |
Maximum voltage for accelerator pedal at idle in Level II |
|
SPSVG_UM |
Threshold full load for switch over of max. tolerance |
|
SQRTUTUN |
square root from ratio ambient temperature to standard temperature |
|
SQRTUTUN |
square root from ratio ambient temperature to standard temperature |
|
SQRTUTUNVP |
square root from ratio ambient temperature to standard temperature |
|
SRKTEVS |
Manifoild time constant when closing the canister purge valve |
|
STANENCODE |
Code PID $1551 - Remote Vehicle Start Disable History |
|
STLDIA1 |
Grid point1 for boost control adaption |
|
STLDIA2 |
Grid point2 for boost control adaption |
|
STLDIA3 |
Grid point3 for boost control adaption |
|
STLDIA4 |
Grid point4 for boost control adaption |
|
STPULEATST |
Start pulse length for test pulses - MSV output stage diagnosis |
|
SULSULUFT |
Threshold value for plausibility fault LSU at air |
|
SULSULUFTL |
Threshold value for plausibility fault LSU at air, on low gain |
|
SULSUMN |
Threshold value for plausibility fault during B_sa |
|
SULSUMX |
Threshold value for plausibility fault CJ110 |
|
SULSUMX |
Threshold value for plausibility fault CJ110 |
|
SULSUMXL |
Threshold value for plausibility fault CJ110, on low gain |
|
SULSUMXL |
Threshold value for plausibility fault CJ110, on low gain |
|
SVFDKSRF |
level detection of vehicle stop for throttle self-cleaning-function |
|
SWMSVHSSD |
number of debouncing attempts of msv high-side-swich |
|
SWWDKADERR |
Max distance to the break point for realtive error calculation |
|
SYNAES |
mode of synchronization to enable injection |
|
SYNAES |
mode of synchronization to enable injection |
|
SZANSSM1 |
switching level 1 of afterstart enrichment |
|
SZANSSM2 |
switching level 2 of afterstart enrichment |
|
SZOUTMIN |
Minimum dwell time |
